Product ID:TIGTECTIC 2-24
MSDS Date:11/12/1991
FSC:3439
NIIN:00N034448
MSDS Number: BPXRY

EUTECTIC CORP

40-40 172ND ST
FLUSHING, NY 11358-2799
US

Emergency Phone: 718-358-4000

Info Phone: 718-358-4000

Cage: 72271

EUTECTIC CORP

CHARLOTTE, NC 28273 US

Telephone: 704-527-9800/ 800-221-1433

Cage: 72271

NICKEL

CAS: 7440-02-0

RTECS: QR5950000

Fraction By Weight: >50%

OSHA PEL 1 MG/M3

ACGIH TLV: 1 MG/M3

TITANIUM. PEL & TLV AS TITANIUM DIOXIDE.

CAS: 7440-32-6

RTECS: XR1700000

OSHA PEL 10 MG/M3 TDUST

ACGIH TLV: 10 MG/M3 TDUST

TRAIN WORKERS NOT TO TOUCH LIVE ELEC PARTS & TO

RTECS: 9999999ZZ

GASEOUS RXN PROD MAY INCL OZONE, CO, CO*2,

RTECS: 9999999ZZ

ONE RECOM WAY TO DETERM THE COMPOSITION & QTY OF

RTECS: 9999999ZZ

AIR SAMPLE INSIDE WORKER'S HELMET IF WORN/IN WELDER'S

RTECS: 9999999ZZ

WELDING SOCIETY, P.O. BOX 351040, MIAMI, FL 33135.

RTECS: 9999999ZZ

ENVIRON-A SAMPLING STRATEGY GUIDE', WHICH GIVES

RTECS: 9999999ZZ

LD50 LC50 Mixture:NONE SPECIFIED BY MANUFACTURER.
Routes of Entry: Inhalation:YES Skin:NO Ingestion:YES
Reports of Carcinogenicity:NTP:YES IARC:YES OSHA:NO
Health Hazards Acute and Chronic:LITTLE/NO HAZ EXIST FOR ARC WELD
ELECTRODES & BRAZING RODS BEFORE THEY ARE USED IN WELD PROCESS.
ACUTE:INHAL: FUMES ASSOC W/HEAT, WELD, BRAZ/SOLDER/CUTTING METALS
CAN BE DANGEROUS TO YOUR HLTH & OVERE XP CAN CAUSE LUNG DAM &/OR
OTHER ORGAN DAM. EYE/SKIN: ARC RAYS & ULTRAVIOLET LIGHT CAN INJURE
EYES & (EFTS OF OVEREXP)
Explanation of Carcinogenicity:NICKEL: ANTICIPATED TO BE A CARCINOGEN
(NTP); GROUP 1(IARC).
Effects of Overexposure:HLTH HAZ:BURN SKIN. LIQ USES IN FLUXES & CHEM
AIDS MAY CAUSE IRRIT/POSS CHEM BURNS. INGEST: DANGER! MAY BE
HARMFUL/FATAL. ING 1:SHORT TERM EFTS FROM OVEREXP TO INHAL OF
NICKEL FUMES MAY INCL METALLIC TASTE, NAUS, TIGHTNESS OF CHEST,
FEVER/ALLERGIC RXN. SKIN/EYE CONT MAY CAUSE ALLERGIC RXN. LONG TERM
OVEREXP (SUPP DATA)
Medical Cond Aggravated by Exposure:NONE SPECIFIED BY MANUFACTURER.

First Aid:INHAL: MOVE TO FRESH AIR SOURCE. CONTACT A PHYSICIAN & ADVISE
ON INGRED. SKIN: THORO WASH HANDS/EFFECTED AREAS WITH SOAP & WATER
TO REMOVE ALL RESIDUE. IF RASH/BURN DEVELOPS, CONSULT A PHYSICIAN.
EYE: THORO FLUSH WITH WATER FOR AT LEAST 15MIN TO REMOVE ALL
RESIDUE. OBTAIN PROMPT MED ADVICE FOR FLUXES & CHEM AIDS. ADVISE
PHYS ON INGRED. INGEST: CALL PHYS &/OR LOC POIS CTL CTR. ADVISE ON
INGRED.

Flash Point:NON-FLAMMABLE
Extinguishing Media:CO*2, DRY CHEMICAL FOAM TYPE.
Fire Fighting Procedures:WEAR NIOSH/MSHA APPROVED SCBA AND FULL
PROTECTIVE EQUIPMENT . TOXIC FUMES MAY BE PRODUCED.
Unusual Fire/Explosion Hazard:WELD ARC/SPARKS/FLAMES CAN IGNITE COMBUST
& FLAMM. SOME FLUXES & CHEM AIDS MAY GIVE OFF HCL, PHOSGENE &
CHLORINE GASES. CANS, UNDER PRESS, & FLAMM MAY EXPLODE.

Spill Release Procedures:NONE SPECIFIED BY MANUFACTURER.
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.

Handling and Storage Precautions:NONE SPECIFIED BY MANUFACTURER.
Other Precautions:PLEASE READ & UNDERSTAND PROD LBL INFO FOR PROPER
PROC & USE. SEE ANSI Z49.1 "SAFTY IN WELDING & CUTTING", & CHAPTER
11 OF "THERMAL SPRAYING", PUBLISHED BY AMERICAN WELDING SOCIETY &
OSHA PUBLICATION 2206 (29CFR1910) FOR MORE DETAIL.

Respiratory Protection:IF WORK STATION IS NOT PROPERLY VENTILATED TO
EXHAUST ALL FUMES, VAPORS & DUSTS BELOW RECOMMENDED EXPOSURE LIM,
USE A NIOSH/MSHA APPROVED RESPIRATOR.
Ventilation:USE ENOUGH GEN VENT & LOC EXHAUST @ WORK SITE TO KEEP ALL
FUMES & DUST FROM WORKER'S BRTHG ZONE & GEN AREA. (SUPP DATA)
Protective Gloves:WELDER'S GLOVES.
Eye Protection:CHEM WORK GOG OR FULL LNGTH FSHLD.
Other Protective Equipment:WEAR HAND, HEAD, & BODY PROT WHICH HELPS TO
PVNT INJURY FROM RADIA, SPARKS & ELEC SHOCK. @ A MINIMUM, THIS
(SUPP DATA)
Work Hygienic Practices:NONE SPECIFIED BY MANUFACTURER.
Supplemental Safety and Health
EFTS OF OVEREXP: TO NICKEL & NICKEL CMPDS MAY CAUSE LUNG
FIBROSIS/PNEUMOCONIOSIS. STUDIES OF NICKEL REFINERY WORKERS
INDICATED A HIGHER INCIDENCE OF LUNG & NASAL CANCERS. VENT: TRAIN
WELDER TO KEEP FA CE AWAY FROM FUME/DUST PLUME. OTHER PROT EQUIP:
INCL ARM PROTECTORS/APRONS, HATS AS WELL AS DARK, PROT CLTHG. (ING
3)

HCC:N1
Appearance and Odor:NONE SPECIFIED BY MANUFACTURER.

Stability Indicator/Materials to Avoid:YES
NONE SPECIFIED BY MANUFACTURER.
Stability Condition to Avoid:NONE SPECIFIED BY MANUFACTURER.
Hazardous Decomposition Products:COMPLEX OXIDES OF METALS IN INGRED
SECT; FLUX COATINGS MAY PRDCE FLUORIDE CMPDS, METAL OXIDES, CARBON
& SILICA. (ING 4)

Waste Disposal Methods:DISPOSE OF WASTE MATERIAL POWDERS, GRINDING, OR
FILTER RESIDUES IN ENVIRONMENTALLY SENSITIVE MANNER IN ACCORDANCE
WITH FEDERAL, STATE & LOCAL REGULATIONS. USE APPROP MEASURES TO
KEEP AIRBORNE DUST LEV ELS CONTAINED I/A/W EXPOS LEVELS.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.